Kit/ide1mhz bbc model b & bbc master 128 – Internal Compact Flash Interface Kit



Download 0.6 Mb.
Page1/2
Date28.05.2018
Size0.6 Mb.
#51569
  1   2
KIT/IDE1MHZ - BBC Model B & BBC Master 128 – Internal Compact Flash Interface Kit

Thanks for buying this IDE Interface kit from me at RetroClinic. The BBC/IDE interface component of this kit is my own, new single chip custom programmable logic design, made to be compatible with various IDE patched operating systems for the BBC and Master Series Computers.

Connections on the interface are very straightforward:


  • 1MHz BUS – This connects to the 34 way 1MHz bus connector underneath your Beeb. Ensure you do NOT connect it to the floppy drive, although no damage should result if you do, I say “SHOULD”, so best not to try!

  • Compact Flash socket – where the CF card plugs in!

  • PWR – USE THE POWER CONNECTOR ON THE IDE INTERFACE, NOT THE ONE NEAR THE CF CARD! This is pin compatible with the standard 3.5” floppy drive power connector, in that pin 1 is +12v (unused), pins 2-3 are 0v (GND, Black cable), and Pin 4 is +5v (Red cable). There is no power supplied through the1MHz bus, so this connection is needed.

There is one jumper on the IDE interface – JP1, which when connected, supplies 5v through pin 20 of the interface to power CF adaptors that can use this facility. The CF adaptor supplied uses this, so leave this jumper on. The ACT light shows when the drive is in use. If you intend to mount this interface in an enclosure, you can desolder the ACT LED, and put a header there to bring the LED to the outside of the case. It is current limited through a 1k resistor, so no extra one is needed.

The IDE interface is 8 bit, as opposed to 16 bit that you would find in an Arc, or your PC. We’re forced to using only 8 bit, because that is the width of the data bus in the Beeb, and what all the operating systems have been written for. There is a 16 bit interface available for the Beeb, but because there’s no support software for it, it still has the same limitations as this 8 bit one. However, 1GB CF Cards are not at all expensive nowadays, and they will format to the full 512MB that ADFS (and many other computers of that era) can handle, so giving you plenty of space to work with. I’ve tested the interface with many cards, and all the ones I’ve tried seem to work just fine, but I can’t warrant that every single card will work perfectly. Some cards are 5v only, some 3.3v only, and some can use both. I have set the power jumper on the CF Interface card – JP2 – to 3.3v, as most cards seem happy at this. If you encounter errors, try putting it to 5v. If this does not work either, then the card may not be compatible, please contact me in this instance to see if I can shed light on the matter.



SOFTWARE

A ROM is supplied in the kit which contains two Different versions of Acorn ADFS. One is ADFS 1.53 for the BBC Master, and the other is ADFS 1.33 for the BBC B.

A Floppy disk of various utilities have also been supplied on DFS disk. Some of these are part of the HADFS suite, a freeware operating system by J.G. Harston, whist others have been purposely written for this application. Use of some of these will be described later in this document, but the main one is “HDINIT”, which is the program that enables you to format CF cards on the interface.

INSTALLATION

Two sets of installation instructions follow, one for the BBC Master, and one for the BBC Model B. At the time of writing, the kit has been tested with the BBC Model B+ 64K and 128K, and has found to operate perfectly with the supplied software. I have not as yet written separate instructions for these models, but they are almost identical to that of the Model B, except for the placement of the ROM. Please look in your B+ reference manual if you need to consult about fitting ROMS to that model, or feel free to contact me for support or updated instructions.



INSTALLATION ON A BBC MASTER 128 - GETTING STARTED

Open up your Master case with the 4 screws under the casing, and put the lid to one side. Gently remove the plastic that contains the speaker and cartridge mount, and place it to one side, being careful not to pull the speaker cable out. If you do dislodge it, it is clearly marked where it should go back, but is under the keyboard, so a pain to get to.

As mentioned above, the ROM supplied contains two sideways ROM images, one for the ADFS 1.53, and the other for ADFS 1.33. Because of this, it can only be placed in either of 2 of the 3 sockets in the Master. I recommend using the lower socket as pictured, which is ROM banks 4 & 5 – this is because Elite requires Sideways RAM bank number 6, which would be taken up if you mounted the ROM on the top socket. Ensure the little “chip” at one end of the ROM faces in the same direction as all the other chips on the board – if you put it in the wrong way round, it will get destroyed. Make sure that all the pins are secured in the socket and that you haven’t accidentally bent one out of shape while inserting it.

Ensure the links near the ROM Sockets are set to the following configuration, as seen in the photo below:



LK19 – West (This selects banks 6 & 7 for Sideways RAM)
LK18 – East (This selects banks 4 & 5 for the ROM socket)
LK12 – Unchanged - this is a configuration for the cartridge slot, and is not used in the CF application, so keep it as it was.

For the Interface, you may wish to route the 1MHz bus cable under the motherboard, or on top for convenience. Either way, you will probably have to remove some plastic of the casing below the socket near the 1MHz bus connector, to route the cable through. If you do route it under the motherboard, it will need to be removed for access.



Next, you need to fit the power cable. Referring to the photo below, unplug the two power connectors to the motherboard at locations PL19 and PL20. Connect the male spade connectors to the power supply wires, ensuring that Red connects with Red, and Black connects with Black. Then, plug the 2 remaining female connectors from the supplied lead, Red into PL19, and Black into PL20. The 2 way terminal block supplied is not used for the Master installation.

Double check that you have the polarities correct, IE Red to Red, Black to Black. If you get them the wrong way round and turn the computer on, you may blow it all up!



You can now mount the Interface PCB in a suitable location. You may wish to mount it on the main PCB, but make sure you don’t attach the sticky pads to a chip that likes to get hot. Best place I think for it is upside down on the case, as shown in the photo below.

Once you have connected the 1MHz bus cable, fitted the ROM and connected the power cable, you can power up the machine, but first do so without a CF card plugged in. Make sure the power red LED comes on on the CF adaptor card. If so, turn off, then insert your CF card, and turn the power back on. Check now the green Card Detect light is also on.

Once you have the Power LED and the Card Detect light, it’s time to reconfigure the machine to use the new ADFS. If one or both are not lighting up, check the connections, reset everything, including detaching the CF card interface from the IDE PCB, and reseat the JP1 jumper. Contact me if you still get no joy at this stage.



Download 0.6 Mb.

Share with your friends:
  1   2




The database is protected by copyright ©ua.originaldll.com 2024
send message

    Main page