Electronic trajectory measurements group the radar roadmap



Download 0.55 Mb.
Page1/10
Date10.03.2018
Size0.55 Mb.
#42762
  1   2   3   4   5   6   7   8   9   10

DOCUMENT 260-98


ELECTRONIC TRAJECTORY

MEASUREMENTS GROUP

THE RADAR ROADMAP


WHITE SANDS MISSILE RANGE

KWAJALEIN MISSILE RANGE

YUMA PROVING GROUND

DUGWAY PROVING GROUND

ABERDEEN TEST CENTER

NATIONAL TRAINING CENTER
ATLANTIC FLEET WEAPONS TRAINING FACILITY

NAVAL AIR WARFARE CENTER - WEAPONS DIVISION

NAVAL AIR WARFARE CENTER - AIRCRAFT DIVISION

NAVAL UNDERSEA WARFARE CENTER DIVISION, NEWPORT

PACIFIC MISSILE RANGE FACILITY

NAVAL UNDERSEA WARFARE CENTER DIVISION, KEYPORT
30th SPACE WING

45th SPACE WING

AIR FORCE FLIGHT TEST CENTER

AIR FORCE DEVELOPMENT TEST CENTER

AIR WARFARE CENTER

ARNOLD ENGINEERING DEVELOPMENT CENTER

GOLDWATER RANGE

UTAH TEXT AND TRAINING RANGE

DISTRIBUTION A: APPROVED FOR PUBLIC RELEASE;

DISTRIBUTION IS UNLIMITED

DOCUMENT 260-98


THE RADAR ROADMAP

SEPTEMBER 1998

Prepared by
Electronic Trajectory Measurements Group

Range Commanders Council

Published by
Secretariat

Range Commanders Council

U.S. Army White Sands Missile Range

New Mexico 88002-5110

TABLE OF CONTENTS

Page

Preface v
Abstract vi

A-1 Uniform Distribution of Elements within a Circular Aperture A-12 viii

1.0 Introduction 1

2.0 The Ultimate Instrumentation Radar 2

2.1 Full Coherence. Many of today's instrumentation radars are coherent, meaning the phase relationship between the transmit and received pulses is maintained or measured. Coherence allows measurement of phase change due to motion relative to the radar, whether the motion is translational or rotational. Coherence also implies Doppler measurement capability since Doppler is the negative time derivative of phase. Assuming adequate motion compensation, Doppler can be highly resolved, and highly resolved Doppler is an essential component of radar imaging. Coherent radars can be fully coherent or coherent-on-receive. Fully coherent radars are, as the label suggests, coherent under all conditions. By contrast, the typical coherent-on-receive radar is coherent only in the first range ambiguity, or when the target is close enough for the first pulse to return before the next is transmitted. Many of today's instrumentation radars are fully coherent (e.g., AN/MPS-36 and AN/MPS-39 a.k.a. MOTR). Therefore, little development will be required to make the MO-UIR fully coherent. (Applicable to SOT; inherent to CW.) 2

2.2 High-Range Resolution. High-range resolution is achieved through wide bandwidth. Typically, the frequency of each transmit pulse is linearly swept over the entire bandwidth. The greater the swept bandwidth, the smaller the resolution of the range measurement. A bandwidth of 500 MHz yields a range resolution of about one foot. High range resolution is, along with Doppler resolution, an essential component of radar imaging. Most of today's instrumentation radars do not have high range resolution, but the techniques are well-known, the technology is mature, and relatively little development will be needed to incorporate it into the MO-UIR. The requirements are that (1) the signal be digitally generated, highly stable and low noise, and (2) frequency steering of the phased array by the frequency chirp be kept within acceptable bounds. (Applicable to SOT but not CW.) 2

2.3 Digital Waveform Generation. Digital waveform generation is the process for obtaining the linear FM sweep needed for high range resolution. The technology already exists for digitally generating the linear FM sweep, so little development is needed in this area. (Applicable to SOT but not CW.) 3

2.4 Active Phased Array. A phased array will be necessary for the radar to track multiple objects with any appreciable angular extent. The typical single-object tracker dish antenna has a field of view of 1o or less, whereas multiple-object instrumentation radars can have a 60o field of view. MOTR has a phased array so no phased array development is needed per se. However, the MO-UIR needs an active phased array. Rather than providing a high power RF field to an array which introduces a phase shift at each element in order to form the beams, the active array will contain a low-power amplifier at each element and low power illumination of the array (or no illumination if each element contains a transmitter). These elements will be solid state components and will be capable of near-CW operation. This means that very high duty ratios (up to 50%) will be possible, thus greatly boosting the average power, hence the loop gain, and hence the tracking range of the radar. A radar like MOTR could, when equipped with an active phased array, track small orbiting satellites. An active array will also exhibit the graceful degradation promised for phased arrays, but often rendered irrelevant by the single-point failure of the high-power transmitter. A considerable amount of time and effort will be needed to develop an affordable active array for the MO-UIR. (Not applicable to either SOT or CW.) 3

2.5 Digital Beam Forming. A phased array allows the use of digital beam forming, a process of digitizing and recording the output of each array element so that, in subsequent computer processing, multiple beams and strategically placed nulls can be created. By creating multiple beams on receive, multiple objects can be tracked simultaneously at the system PRF instead of sub-multiples of the system PRF, and beams can be formed to locate items of interest that were illuminated but not tracked. On the transmit side, the beam can be shaped to illuminate just those objects of interest. Digital beam forming, if included, must be an integral part of the active array development and stretch processing will have to be included to keep the number of recorded samples manageable. (Not applicable to either SOT or CW.) 3

2.6 Radar Control Language. The MO-UIR will need to be able to track multiple objects in a complex, rapidly changing environment -- a situation that will often overtax the human operator. To remedy this situation, a radar control language (RCL) will be developed. RCL will be a high level language that is programmed prior to the mission to control the radar in real-time. It will be possible to program for deployments, dispenses, intercepts and other events, changing the radar's behavior as the test scenario unfolds. Development of the RCL should be straightforward but it must be done carefully, since RCL will have to make operator-type decisions in real-time. An expert system may have to be developed to help program the RCL. (Applicable to SOT but probably not needed for CW.) 3

2.7 Automated Setup and Calibration. The MO-UIR will be automated for set-up and calibration. Setup includes tuning the radar, verifying the loop gain, testing the performance of transmitter and receiver, phasing receiver channels, scaling error gradients, and increasingly, setting parameters and verifying the correct operation of software-based subsystems. Calibration includes measurement and validation of the systematic errors that affect a radar track, calibrating the range and angle measurements, and setting in delay values for transponders. Calibration is what sets instrumentation radars apart from surveillance radars and other tracking radars. Instrumentation radars must be set up and calibrated frequently to ensure the necessary accuracy and precision. Automating these processes will greatly reduce the effort needed and hence the number of highly-skilled personnel. Many instrumentation radars have some degree of automated calibration already. Some additional development will be needed to more fully automate calibrations, but this should be straight-forward engineering. (Applicable to SOT; perhaps applicable to CW.) 4

2.8 Real-Time Data Recording, Processing and Display. All data collected and all actions taken by the MO-UIR must be recorded for subsequent processing and analysis. Many of the measurements will be obtained and displayed in real-time (e.g., Range-Time-Intensity or RTI plots). Other measurements such as miss distance, attitude and damage assessment will rely on radar imaging which requires an extensive amount of processing on an expert-system imaging workstation and, in the case of miss distance, requires the combination of data from multiple radars. Most of the radar signal processing development has or will have been done by the time the MO-UIR is developed. White Sands Missile Range (WSMR) has developed a radar imaging workstation under contract with MARK Resources, Inc., Torrance, CA during the past two years. Work has begun on the expert system to assist in the processing of the data. Some other development will be needed on the real-time recording and display, but this should be straight-forward engineering. (Applicable to SOT and CW.) 4

2.9 Real-Time Control. In real-time, the MO-UIR will be controlled in a variety of ways. First, it will be controlled in general by a human operator. Second, it will be controlled by the radar control language which will be programmed and activated by the human operator. Third, it will be guided by an expert system. Fourth, it will be synchronized with other radars by a central control facility so that the high-duty pulses of one radar do not interfere with another radar. And fifth, it's overall operation and data products, raw or finished, will be coordinated by the central control facility in charge of the test. Data from all sensors will be collected and fused in real-time at a central site. (Applicable to SOT and CW.) 4

2.10 Reliability. The MO-UIR will be designed and built to be reliable, -- both the equipment and the calibration of the radar. Present instrumentation radars are maintained and operated by highly skilled on-site technicians who are constantly repairing and/or calibrating to keep the radar in top condition. Future radars will have to be more reliable because (1) they may have to be operated remotely and (2) the number of highly-skilled technicians will be reduced to reduce labor costs. Improved reliability will mean added initial costs but the engineering to achieve the reliability is straightforward. A reliable design should also use modular units, as this eases maintenance and improves the availability of the system. The design should also avoid, as much as possible, components or subsystems that the marketplace does not support. The use of reliable, modular, and Commercial Off-The-Shelf (COTS) components should be a goal of new radar subsystem designs. (Applicable to SOT and CW.) 4

2.11 Polarization Diversity. The MO-UIR probably will not have polarization diversity. It would be extremely difficult to implement in a phased array. It may be used in some SOTs, however, where measurement of polarization is important to the test (e.g., verifying missile seeker characteristics). (Applicable to SOT.) 5



3.0 MOTR vis-à-vis the Multiple-Object UIR 5

4.0 The Radar Roadmap (i.e., the plan) 5

4.1 Multiple-Object Ultimate Instrumentation Radar (MO-UIR). The MO-UIR will take several years to develop and should be pursued as a tri-service effort. The development of the active phased array, with digital beam forming, should be begun immediately because it is the highest risk, longest lead time item. An operational radar should be possible within ten years. MO-UIR developments should be closely coordinated with the MOTR developments, working toward the point where the two converge (i.e., where any MOTR can be upgraded to become an MO-UIR). Designing for ultra reliability should be a very high priority. 6

4.2 Multiple-Object Trackers. Where requirements now exist for multiple-object trackers, the modernized MOTR should be purchased. It is a very versatile radar, capable of tracking forty objects and collecting data in multiple range gates. It is a fully coherent, 1 MW radar with system PRF of 2560 and pulse widths of ¼, ½, 1, 3 1/8, 12½ and 50 µs. Its major deficiency is the lack of bandwidth (i.e., range resolution). It is also a very costly radar, but the cost varies considerably with the number purchased. The manufacturer has recently quoted the following prices: $30M for one, $50M for two ($25M apiece) and $60M for three ($20M apiece). The three services should go together to purchase at least three MOTRs so the price savings can be realized. Actually, we have already identified the need for 7 to 9 additional MOTRs: WSMR, NM (2), ESMC at Cape Canaveral, FL (1), WSMC at VAFB, CA (1), NAWC at Pt Mugu, CA (1 or 2), PMRF at Barking Sands, HI (1 or 2), and AFWTF at Roosevelt Roads, Puerto Rico (1). 6

4.3 Single-Object Trackers. For many test and training applications, low-cost single-object trackers are a viable option. Currently, if an AN/FPS-16 radar antenna and pedestal are provided, a new radar can be procured via the Instrumentation Radar Support Program (IRSP) contract for about $2.2M. These radars have the same tracking performance of an original AN/FPS-16, that is: 0.1 mil angular accuracy and about 20 ft range, with noise around 3 - 4 feet. Of course, they provide only range, azimuth and elevation data, since they are neither coherent nor wideband. A program could be initiated with the IRSP contractor to convert these to a modular design. The same electronics could be used with different pedestals, the radar could be converted to use a 1 MW klystron or a cross field amplifier to provide stable output for use with moving target indicator (MTI) or pulse Doppler tracking. A larger 5 MW transmitter could be used with an existing 30 ft dish for high power applications. As much as possible, high-power solid state transmitters should be used, as has been done at the Air Force Eastern and Western Ranges. MTI, remote control, and Doppler tracking could be modular additions. Already the IRSP radar is modularized, although some functions in control, ranging, and data handling could be more effectively combined into a single computer chassis with reduction in wiring and parts. The contractor has built different parts of the radar at different times to sell to various domestic and foreign customers, so some parts are of current design and others are nearly obsolete. Development funds should be provided to produce a modular, standardized, single-object tracking radar with options, including Doppler, high range resolution, and other advanced technologies as needed. Regular updating should be done, high priority should be given to improved reliability, and imaging capability should be added as needed. 6

4.4 Imaging Radars. The current instrumentation radars (whether a single or multiple object tracker) can be augmented by a small, special purpose, slaved (i.e., non-tracking), wideband data collecting radar. WSMR and MARK Resources have designed such a radar. Other characteristics of this radar include the following: X-band (8.5 - 10.55 GHz), transportable, monostatic, 500 MHz (1 ft resolution), solid state, digitally generated linear FM chirp, digital pulse compression, 15 to 140 km ranges (but easily extendible to 280 km), 1o or 2o beamwidth, 1000 to 2000 s/s PRF, RTI plots displayed in real-time, quick-look image processing and data combination on specialized workstation recently developed. Four of these radars are needed to accurately measure attitude, miss distance, object deployment and extent of damage at ranges up to 140 km. Cost of one system, including five radars (one spare) and associated equipment, is expected to be $15M or less. This system, being all solid state, should be very reliable. CTEIP funding for these new imaging radars should be provided. 7

4.5 CW Radars. In many tests, the customer needs to know what happened and when it happened, that is, to identify and characterize events. Often these events occur early in the launch of a missile but also occur frequently in the terminal period when munitions of one type or another are dispensed by either missiles or projectiles. These events often can be adequately characterized by their Doppler, provided the Doppler ambiguity interval is sufficiently wide. Although coherent pulsed radars can obtain Doppler on the tracked objects, the ambiguity interval is usually too small to allow the various Doppler's to be sorted out. CW radars, by contrast, have a theoretically infinite ambiguity interval which can be digitized at a rate high enough to preserve the necessary Doppler interval. CW radars are also excellent for providing TSPI on direct fire weapons and mortars. Small transportable, solid state CW radars are inexpensive, typically $1M - $3M. They are also very reliable. Each range should buy CW radars and incorporate advanced technologies as needed. 7

4.6 Data Fusion. Radar data products are being improved at many of the ranges by merging radar data with data from other instrumentation systems. For example, video trackers, mounted on a radar antenna can be used to track objects visually. A new data fusion concept is merging radar data with data from the Global Positioning System (GPS). For this a GPS receiver is connected to a radar transponder and provides a convenient link from the airborne GPS receiver to the ground. Other examples are use of infrared optics and laser trackers with radars, and the use of radar range measurements to automatically focus optical systems. Each subsystem uses its own strengths to boost the overall quality of the data product. Data fusion should be a high priority at ranges that utilize multiple sensors. 8

4.7 Pre-mission Planning. Pre-mission planning and simulation are being developed or improved at several ranges. The customers themselves often simulate the test to be performed (e.g., the encounter of a re-entry vehicle and a theater defense missile), so the range planner does not have to do anything in this regard. However, the radar planner needs to simulate the placement and performance of the instruments in conjunction with the simulated test. In effect, the planner must demonstrate to all parties that (1) no radar will be lost to terrain shadowing, ground clutter, low S/N, etc. and (2) the data will be sufficiently accurate for the purposes intended. As test resources shrink, and hence fewer and fewer tests are conducted, it becomes imperative that the few tests conducted be conducted successfully. Therefore, pre-mission planning and simulation become more valuable every year. Each range should incorporate technologies for pre-mission planning as needed. 8

4.8 Miscellaneous. First, specialized uses of instrumentation radars should be considered as particular circumstances of the test/training ranges dictate. These include fine-line Doppler tracking, multiple-object tracking in the single beam of a dish antenna (e.g., the tracking of incoming multiple warheads/decoys or dispensed submunitions), and increased angle resolution through the use of multiple mutually-coherent radars. And second, alternative technologies such as impulse radar and multiple-object bistatic radars should continue to be studied. The former allows high resolution without the use of pulse compression techniques and the latter promises cheaper systems by using a single transmitter to illuminate the target for multiple receivers. 8

5.0 Additional Remarks 8

16.0 Upgrading the MOTR System with Segmented Linear FM 16





Appendix A: Issues Concerning the Radar Roadmap A-1

1.0 Choice of Frequency Band A-2

2.0 Assessment of Interference A-3

3.0 Amplitude Weighting on Transmit A-4

4.0 Extended Range A-5

5.0 Extremely Long Range A-6

6.0 Number of Wideband Radars Required A-6

7.0 Ship-Based Wideband Radars A-7

8.0 Combining Multiple Radars into a Large Array A-7

9.0 Long-Baseline Interferometry A-7

10.0 Making an Interferometer Work A-9

11.0 Degradation of Resolution for an Interferometer A-10

12.0 Array Thinning A-11

13.0 Electronic Scan with Wideband Waveforms A-15

14.0 Segmented Linear-FM Waveforms A-15

15.0 Segmented Linear-FM Burst A-16

16.0 Upgrading the MOTR System with Segmented Linear F A-17

17.0 Active Arrays A-17

18.0 Digital Beamforming A-17

19.0 Active Array for Multiple Object Tracker A-18

20.0 Review of the MSTS Concept A-19

21.0 Technology Considerations A-20

References A-21

Appendix B: Rationale For the Roadmap B-1




Appendix C: List of Ranges Contacted or Visited C-1

1.0 Visited C-2

2.0 Briefings and Discussions C-2

3.0 Contacted C-3


LIST OF FIGURES

Page

A-1 Uniform Distribution of Elements within a Circular Aperture A-12


A-2 Antenna Pattern for Element Distribution in Figure A-1 A-12

A-3 Concentration of Elements in Center of Aperture A-13

A-4 Antenna Pattern for Element Distribution in Figure A-3 A-14

A-5 Residual Phase After Demodulation of Segmented Waveform A-16


Preface

The Radar Roadmap is a new type of document for the Range Commanders Council (RCC) Electronic Trajectory Measurements Group (ETMG). This document is a statement from the technical community of the instrumentation radar requirements for 10, 20, and even 30 years into the future. Like an automobile roadmap, it is intended to show where we can go and the best routes to get there. It is not a document that shows where we must go. This is the first time a visionary guidance document like this has been attempted by the ETMG. It is our hope that the document will be a living, growing document, with periodic updates.


The Roadmap project is really a joint effort. It is an ETMG document, but it is also intended to satisfy the needs of the Office of the Secretary of Defense (OSD) Central Test and Evaluation Investment Program (CTEIP) manager. A tri-service team, consisting of Christopher Weal (OSD), Donald Sammon (Army, White Sands Missile Range (WSMR)), Richard Stepanian (Air Force (30th Space Wing), and Grant Mills (Naval Air Warfare Center Weapons Division), put together the radar roadmap. In addition, Elwin Nunn (WSMR), Earl Comstock (Newtech), and Dr. Richard Mitchell (Mark Resources, Inc.) provided significant contributions. Finally, OSD provided a substantial amount of the funding for this effort, particularly for the contractor support.
Abstract

Instrumentation radar has played a very significant role in testing and training for more than 50 years. Along with optics, it has been a major supplier of time-space-position-information (TSPI). With the advent of the Global Positioning System (GPS), the need for instrumentation radar for TSPI has been called into question. Is radar still needed? Or can it be replaced by GPS? The members of the ETMG argue that radar is still needed. A study of requirements at over 25 test and training ranges has shown that radar, far from being passè, is needed more than ever. Radar is needed for TSPI on objects that cannot be instrumented for GPS. It is also needed for a variety of specialized measurements, including radar cross section (i.e., stealthiness), characterization of debris, and assessment of damage at intercept. This paper discusses the future needs of instrumentation radar and presents the radar roadmap (i.e., the plan) for satisfying those needs at the test, training, and operational ranges for 10, 20, and even 30 years into the future.





  1. Download 0.55 Mb.

    Share with your friends:
  1   2   3   4   5   6   7   8   9   10




The database is protected by copyright ©ua.originaldll.com 2024
send message

    Main page